Cold Creek and Where Fillmore’s Landscape Begins in Fillmore, NY

Genesee River flowing past wooded, grassy banks in western New York

Fillmore, New York, begins at a stream mouth. Cold Creek joins the Genesee River here, in the town of Hume in Allegany County, at about 1,200 feet above sea level. Early settlers called the place “The Mouth of the Creek” before renaming it for President Millard Fillmore in 1850. That meeting of creek and river still shapes the ground beneath Fillmore’s buildings and the weather those buildings face, which makes it a useful starting point for anyone responsible for a roof in the area.

The Confluence That Gave Fillmore Its Start

A confluence is the point where two streams meet and merge. At Fillmore, Cold Creek feeds the Genesee River, which rises in Ulysses Township, Potter County, Pennsylvania, at 2,275 feet and flows roughly 157 miles north to Lake Ontario. The river drains a watershed, the total land area whose rain and snowmelt flows into one river, of about 2,500 square miles. Fillmore therefore receives water from a region far larger than its own footprint.

The hamlet sits along the Genesee River, where New York State Routes 19 and 19A meet. Its village government incorporated in 1924 and dissolved in 1994, and the 2020 census counted 596 residents. Small as it is, Fillmore sits inside a landscape of dramatic relief, which brings the surrounding terrain into focus.

Genesee River flowing past wooded, grassy banks in western New York
Image credit: Pollinator at the English-language Wikipedia, CC BY-SA 3.0, via Wikimedia Commons

Terrain and Elevation in Allegany County

Fillmore lies in a county of steep hills and narrow river valleys. Allegany County’s highest point, Alma Hill, reaches 2,548 feet. The Genesee River cuts north through this country and drops over three waterfalls in Letchworth State Park.

Terrain matters to buildings because elevation and exposure change how weather behaves. Valley floors, hillsides, and ridgelines can each experience wind and snow differently, so two commercial buildings a mile apart may face different roofing conditions. Those differences become most visible in winter, when Western New York’s snow pattern takes over.

Winter Conditions and Roof Performance

Western New York winters include lake-effect snow, which forms when cold air crosses the relatively warm water of the Great Lakes and releases snow downwind. The National Weather Service office in Buffalo tracks these events and publishes winter season summaries that show how heavily a given season weighed on the region. Snow is only one part of the picture, because several winter processes work on a roof at once.

Four conditions matter most for roofs in Fillmore:

  • Snow load. Engineers use a ground snow load, the weight of snow expected on the ground at a location, to set minimum roof strength in building codes. Heavy, wet snow adds weight quickly, and drifting can concentrate that weight against parapets and rooftop equipment.
  • Freeze-thaw cycles. Water enters small gaps in membranes, flashing, and shingles, freezes, expands, and thaws again. Repeated cycles widen those gaps over time.
  • Ice dams. An ice dam is a ridge of ice that forms at a roof’s edge when heat escaping through the roof melts snow that then refreezes at the colder eave. The ridge traps meltwater behind it and pushes it under roofing materials.
  • Ponding. Ponding is water that stays on a flat or low-slope roof, one with only a slight pitch, after rain or melt. Standing water adds weight and speeds wear on roofing membranes.

Winter is not the only season that tests roofing here, and Fillmore’s history with the Genesee River shows why drainage deserves attention year-round.

Upper Falls on the Genesee River below the Genesee Arch Bridge in Letchworth State Park, New York
Image credit: Dough4872, CC BY-SA 4.0, via Wikimedia Commons

Flooding and the Lessons of Hurricane Agnes

Flooding has occurred periodically along the Genesee River. The Mount Morris Dam, which went into service in the 1950s, sits downstream of Fillmore, so it does not control flooding upstream in Allegany County. In June 1972, the remnants of Hurricane Agnes flooded Wellsville, Belmont, and other communities, with a National Weather Service maximum official rainfall total of 13.7 inches at Wellsville and unofficial reports above 16 inches.

Floods rarely damage roofs directly. Still, the storms behind them test roof drainage, including the drains, gutters, and scuppers (openings in a parapet wall that let water exit a roof) that move water off a building. Blocked or undersized drainage on a low-slope roof can turn heavy rain into ponding in a matter of hours, and that risk connects naturally to the rules that govern how Fillmore’s buildings are designed.

Building Code Requirements in Fillmore

Commercial structures in Fillmore fall under the Building Code of New York State, which forms part of the Uniform Fire Prevention and Building Code that the state’s Department of State administers. One- and two-family homes follow the separate Residential Code of New York State. Both build on model codes published by the International Code Council, and the commercial code relies on the American Society of Civil Engineers’ ASCE 7 standard for minimum snow loads.

Local code enforcement officials apply these rules to new construction and to many reroofing and repair projects. Because the code ties roof design to ground snow load, the same snow that settles on Allegany County’s hills sets the structural expectations for roofs in the valley below. Understanding those expectations starts with understanding the landscape.

That landscape starts at Cold Creek. A small stream meeting a large river created Fillmore’s name, its first settlement, and its exposure to flood, snow, and freeze. Each of those forces still acts on the roofs of commercial properties in Fillmore.

Share this article

Request Estimate